ActionNews
2004-04-04, 15:34:12
Hallo!
Vielleicht könnt ihr mir helfen. Hab einen neuen Rechner (Scaleo 600 AMD64). Darin ist ein Mainboard von FSC (D1607 mit K8T800 Chipsatz) und einem ADMtec AN983 onboard LAN-Chip verbaut. Nun hab ich mir die Mandrake 10 AMD64Beta1 installiert und die Karte wird auch erkannt. Nur bekomme ich kein funktionsfähige verbindung. Wenn ich einen anderen Rechner anpingen will kommt folgendes:
[mike@Scaleo mike]$ ping 192.168.0.2
PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
64 bytes from 192.168.0.2: icmp_seq=1 ttl=128 time=0.349 ms
wrong data byte #30 should be 0x1e but was 0x29
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 29 e4 22 d7 29 e4 22 d7 29 e4 22 d7 29 e4 22 d7 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=2 ttl=128 time=0.172 ms
wrong data byte #30 should be 0x1e but was 0x0
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 0 1 3 3 0 1 3 3 0 1 3 3 0 1 3 3 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=3 ttl=128 time=0.162 ms
wrong data byte #30 should be 0x1e but was 0xa
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d a 4d 58 3a a 4d 58 3a a 4d 58 3a a 4d 58 3a 1e 1f
#48 20 21 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=4 ttl=128 time=0.176 ms
wrong data byte #30 should be 0x1e but was 0x0
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 0 0 c0 a8 0 0 c0 a8 0 0 c0 a8 0 0 c0 a8 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=5 ttl=128 time=0.164 ms
wrong data byte #30 should be 0x1e but was 0x50
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 50 0 0 0 50 0 0 0 50 0 0 0 50 0 0 0 1e 1f
#48 20 21 1e 1f 20 21 1e 1f
--- 192.168.0.2 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3999ms
rtt min/avg/max/mdev = 0.162/0.204/0.349/0.074 ms
Soweit ich herausgefunden habe sollen fast alle Distris gepatchte Tulip-Treiber verwenden (den Tulip brauche ich für den AN983), aber der soll damit nicht mehr richtig funktionieren. Man soll sich deshalb den original Tulip-Treiber besorgen und selber kompilieren. Das Problem ist wo bekomme ich einen dieser Original-Treiber für den Kernel 2.6 her ?
Bzw. weiß jemand einen anderen Rat?
CU ActionNews
Vielleicht könnt ihr mir helfen. Hab einen neuen Rechner (Scaleo 600 AMD64). Darin ist ein Mainboard von FSC (D1607 mit K8T800 Chipsatz) und einem ADMtec AN983 onboard LAN-Chip verbaut. Nun hab ich mir die Mandrake 10 AMD64Beta1 installiert und die Karte wird auch erkannt. Nur bekomme ich kein funktionsfähige verbindung. Wenn ich einen anderen Rechner anpingen will kommt folgendes:
[mike@Scaleo mike]$ ping 192.168.0.2
PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
64 bytes from 192.168.0.2: icmp_seq=1 ttl=128 time=0.349 ms
wrong data byte #30 should be 0x1e but was 0x29
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 29 e4 22 d7 29 e4 22 d7 29 e4 22 d7 29 e4 22 d7 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=2 ttl=128 time=0.172 ms
wrong data byte #30 should be 0x1e but was 0x0
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 0 1 3 3 0 1 3 3 0 1 3 3 0 1 3 3 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=3 ttl=128 time=0.162 ms
wrong data byte #30 should be 0x1e but was 0xa
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d a 4d 58 3a a 4d 58 3a a 4d 58 3a a 4d 58 3a 1e 1f
#48 20 21 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=4 ttl=128 time=0.176 ms
wrong data byte #30 should be 0x1e but was 0x0
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 0 0 c0 a8 0 0 c0 a8 0 0 c0 a8 0 0 c0 a8 1e 1f
#48 20 1d 1e 1f 20 21 1e 1f
64 bytes from 192.168.0.2: icmp_seq=5 ttl=128 time=0.164 ms
wrong data byte #30 should be 0x1e but was 0x50
#16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 50 0 0 0 50 0 0 0 50 0 0 0 50 0 0 0 1e 1f
#48 20 21 1e 1f 20 21 1e 1f
--- 192.168.0.2 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3999ms
rtt min/avg/max/mdev = 0.162/0.204/0.349/0.074 ms
Soweit ich herausgefunden habe sollen fast alle Distris gepatchte Tulip-Treiber verwenden (den Tulip brauche ich für den AN983), aber der soll damit nicht mehr richtig funktionieren. Man soll sich deshalb den original Tulip-Treiber besorgen und selber kompilieren. Das Problem ist wo bekomme ich einen dieser Original-Treiber für den Kernel 2.6 her ?
Bzw. weiß jemand einen anderen Rat?
CU ActionNews