Problem mit SD-Card Reader ToPIC100 im Notebook

[schussel]

Hallo!

Ich habe ein Toshiba Notebook (Satellite) mit einem SD-Card Reader. Als OS läuft Win und Kubuntu Feisty Fawn (7.04) im Dual-Boot.

Die Ausgabe von lspci bringt mir folgenden Card-Reader zu Tage:

02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)

Aber leider habe ich ihn bisher noch unter keiner Linux-Distri zum Laufen gebracht. Unter Windows kein Problem, Treiber gibts bei Toshiba etc.


Unter google habe ich auch schon einiges gelsen, auch dass Card-Reader in Notebooks zum Teil sehr stiefmuetterlich behandelt werden von den Distributionen.

Wer von Euch hat evtl. diesen Card Reader Typen oder weiss wie ich ihn aktiviert bekomme?



Vielleicht noch mehr Infos? Hier die Ausgabe von lspci -v

02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)
Subsystem: Toshiba America Info Systems Unknown device 0001
Flags: bus master, slow devsel, latency 168, IRQ 3
Memory at c2007000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=0
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 48000000-4bfff000
I/O window 0: 00003400-000034ff
I/O window 1: 00003800-000038ff
16-bit legacy interface ports at 0001

02:0d.0 System peripheral: Toshiba America Info Systems SD TypA Controller (rev 05)
Subsystem: Toshiba America Info Systems Unknown device 0001
Flags: medium devsel, IRQ 3
Memory at c2006800 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>

[gentoo]

Normalerweise sind die CR standardmässig aktiviert.

Gib doch einfach mal eine Card in den Slot und sieh nach,
ob du ein sd** device unter /dev hast ( z.B.: sda1, sdb1, sdc2 usw. )

mfg,
gentoo

[schussel]

Hallo!

Unter /dev ist nix zu finden. Da liegt nur scd0, sda, sda1 - sda9.

Bei 5 Partitionen gehören die meisten davon also zur Festplatte.

Es poppt auch kein Fenster auf, wie bei CD etc. wenn ich eine Karte in den Reader stecke.

Karte ist auch formatiert und Dateien sind auch drauf.


Unter Edgy hat das Ding auch schon nicht funktioniert. Aber mit dem neuen Kernel in Feisty....


Unter Dapper und (davor) Suse weiss ich nicht mehr obs ging. Damals war es auch nicht wichtig. Aber mittlerweile habe ich einige SD-Karten die ich gerne benutzen würde.

[MadMan2k]

Card einstecken und danach die asugabe von dmesg posten.

[Gast]

sudo dmesg -c
# Karte reinstecken
dmesg
# Ausgabe kopieren

[schussel]

OK!

Ihr habt es nicht anders gewollt. Ich hätte Euch auch mit | grep was rausgeschnitten..... ;)


0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000004000 end: 00000000000d4000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000002fe60000 end: 000000002ff60000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000002ff60000 size: 000000000000a000 end: 000000002ff6a000 type: 3
[ 0.000000] copy_e820_map() start: 000000002ff6a000 size: 0000000000001000 end: 000000002ff6b000 type: 2
[ 0.000000] copy_e820_map() start: 000000002ff6b000 size: 0000000000005000 end: 000000002ff70000 type: 4
[ 0.000000] copy_e820_map() start: 000000002ff70000 size: 0000000000090000 end: 0000000030000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ffb80000 size: 0000000000080000 end: 00000000ffc00000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000002ff60000 (usable)
[ 0.000000] BIOS-e820: 000000002ff60000 - 000000002ff6a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000002ff6a000 - 000000002ff6b000 (reserved)
[ 0.000000] BIOS-e820: 000000002ff6b000 - 000000002ff70000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000002ff70000 - 0000000030000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 767MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 196448) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 196448
[ 0.000000] HighMem 196448 -> 196448
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 196448
[ 0.000000] On node 0 totalpages: 196448
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1502 pages used for memmap
[ 0.000000] Normal zone: 190850 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 TOSHIB ) @ 0x000f7a10
[ 0.000000] ACPI: RSDT (v001 TOSHIB 750 0x00970814 MASM 0x06110000) @ 0x2ff63fd8
[ 0.000000] ACPI: FADT (v002 TOSHIB 750 0x20030101 MASM 0x61100000) @ 0x2ff69d03
[ 0.000000] ACPI: SSDT (v001 TOSHIB A0007 0x00970814 MSFT 0x0100000e) @ 0x2ff69d87
[ 0.000000] ACPI: DBGP (v001 TOSHIB 750 0x00970814 MASM 0x61100000) @ 0x2ff69fa4
[ 0.000000] ACPI: BOOT (v001 TOSHIB 750 0x00970814 MASM 0x06110000) @ 0x2ff69fd8
[ 0.000000] ACPI: DSDT (v001 TOSHIB A0007 0x20030806 MSFT 0x0100000e) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 30000000:cfb80000)
[ 0.000000] Detected 1496.282 MHz processor.
[ 6.499714] Built 1 zonelists. Total pages: 194914
[ 6.499718] Kernel command line: root=UUID=f5df8da8-c381-42cc-836d-1cfdf181df9d ro quiet splash
[ 6.499918] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 6.499925] mapped APIC to ffffd000 (0160c000)
[ 6.499929] Enabling fast FPU save and restore... done.
[ 6.499932] Enabling unmasked SIMD FPU exception support... done.
[ 6.499941] Initializing CPU#0
[ 6.500005] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 6.502210] Console: colour VGA+ 80x25
[ 6.502820] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 6.503488] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 6.527859] Memory: 767808k/785792k available (1992k kernel code, 17404k reserved, 893k data, 328k init, 0k highmem)
[ 6.527871] virtual kernel memory layout:
[ 6.527873] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 6.527874] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 6.527876] vmalloc : 0xf0800000 - 0xff7fe000 ( 239 MB)
[ 6.527878] lowmem : 0xc0000000 - 0xeff60000 ( 767 MB)
[ 6.527879] .init : 0xc03d7000 - 0xc0429000 ( 328 kB)
[ 6.527881] .data : 0xc02f2264 - 0xc03d16d4 ( 893 kB)
[ 6.527882] .text : 0xc0100000 - 0xc02f2264 (1992 kB)
[ 6.527886] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 6.607957] Calibrating delay using timer specific routine.. 2994.68 BogoMIPS (lpj=5989377)
[ 6.608009] Security Framework v1.0.0 initialized
[ 6.608016] SELinux: Disabled at boot.
[ 6.608037] Mount-cache hash table entries: 512
[ 6.608191] CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
[ 6.608203] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 6.608206] CPU: L2 cache: 1024K
[ 6.608209] CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
[ 6.608220] Compat vDSO mapped to ffffe000.
[ 6.608225] Remapping vsyscall page to ffffe000
[ 6.608237] Checking 'hlt' instruction... OK.
[ 6.624043] SMP alternatives: switching to UP code
[ 6.624220] Freeing SMP alternatives: 11k freed
[ 6.624418] Early unpacking initramfs... done
[ 7.000434] ACPI: Core revision 20060707
[ 7.000848] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 7.004972] ACPI: setting ELCR to 0200 (from 0c98)
[ 7.005124] CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05
[ 7.005130] SMP motherboard not detected.
[ 7.005132] Local APIC not detected. Using dummy APIC emulation.
[ 7.005169] Brought up 1 CPUs
[ 7.005432] Booting paravirtualized kernel on bare hardware
[ 7.005497] Time: 23:41:06 Date: 03/22/107
[ 7.005530] NET: Registered protocol family 16
[ 7.005619] EISA bus registered
[ 7.005624] ACPI: bus type pci registered
[ 7.005700] PCI: PCI BIOS revision 2.10 entry at 0xfd981, last bus=4
[ 7.005703] PCI: Using configuration type 1
[ 7.005705] Setting up standard PCI resources
[ 7.009650] ACPI: Interpreter enabled
[ 7.009653] ACPI: Using PIC for interrupt routing
[ 7.010098] ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 11)
[ 7.010379] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 7 11)
[ 7.010646] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 11) *0, disabled.
[ 7.010921] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *11)
[ 7.011193] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *11)
[ 7.011466] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 7 11)
[ 7.011741] ACPI: PCI Interrupt Link [LNKG] (IRQs *10)
[ 7.012021] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *7 11)
[ 7.012266] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 7.012272] PCI: Probing PCI hardware (bus 00)
[ 7.012711] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 7.013269] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 7.013273] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[ 7.013484] Boot video device is 0000:01:00.0
[ 7.013616] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[ 7.013792] PCI: Transparent bridge - 0000:00:1e.0
[ 7.013849] PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
[ 7.013852] Please report the result to linux-kernel to fix this permanently
[ 7.013871] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 7.015378] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 7.016085] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 7.018940] ACPI: Power Resource [PFAN] (off)
[ 7.019032] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 7.019042] pnp: PnP ACPI init
[ 7.020985] pnp: PnP ACPI: found 11 devices
[ 7.020990] PnPBIOS: Disabled by ACPI PNP
[ 7.021042] PCI: Using ACPI for IRQ routing
[ 7.021045] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 7.027736] NET: Registered protocol family 8
[ 7.027739] NET: Registered protocol family 20
[ 7.028380] PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0
[ 7.028440] PCI: Bridge: 0000:00:01.0
[ 7.028441] IO window: disabled.
[ 7.028446] MEM window: c1000000-c1ffffff
[ 7.028450] PREFETCH window: e0000000-efffffff
[ 7.028459] PCI: Bus 3, cardbus bridge: 0000:02:0b.0
[ 7.028462] IO window: 00003400-000034ff
[ 7.028467] IO window: 00003800-000038ff
[ 7.028472] PREFETCH window: 40000000-43ffffff
[ 7.028477] MEM window: 48000000-4bffffff
[ 7.028481] PCI: Bridge: 0000:00:1e.0
[ 7.028484] IO window: 3000-3fff
[ 7.028490] MEM window: c2000000-c20fffff
[ 7.028494] PREFETCH window: 40000000-43ffffff
[ 7.028510] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 7.028523] PCI: Enabling device 0000:02:0b.0 (0000 -> 0003)
[ 7.028741] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
[ 7.028745] PCI: setting IRQ 3 as level-triggered
[ 7.028749] ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
[ 7.028757] PCI: Setting latency timer of device 0000:02:0b.0 to 64
[ 7.028791] NET: Registered protocol family 2
[ 7.067804] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 7.067954] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 7.069389] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 7.070368] TCP: Hash tables configured (established 131072 bind 65536)
[ 7.070373] TCP reno registered
[ 7.079913] checking if image is initramfs... it is
[ 7.823288] Freeing initrd memory: 6764k freed
[ 7.823539] Simple Boot Flag at 0x36 set to 0x1
[ 7.823734] audit: initializing netlink socket (disabled)
[ 7.823750] audit(1177285266.512:1): initialized
[ 7.823899] VFS: Disk quotas dquot_6.5.1
[ 7.823923] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 7.823986] io scheduler noop registered
[ 7.823989] io scheduler anticipatory registered
[ 7.823992] io scheduler deadline registered
[ 7.824006] io scheduler cfq registered (default)
[ 7.824313] isapnp: Scanning for PnP cards...
[ 8.176999] isapnp: No Plug & Play device found
[ 8.209669] Real Time Clock Driver v1.12ac
[ 8.209734] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 8.210830] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
[ 8.210834] PCI: setting IRQ 4 as level-triggered
[ 8.210838] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[ 8.210849] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[ 8.210938] mice: PS/2 mouse device common for all mice
[ 8.211579] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 8.211854] input: Macintosh mouse button emulation as /class/input/input0
[ 8.211891] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 8.211895] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 8.212084] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 8.219117] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 8.219122] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 8.219264] EISA: Probing bus 0 at eisa.0
[ 8.219271] Cannot allocate resource for EISA slot 1
[ 8.219275] Cannot allocate resource for EISA slot 2
[ 8.219278] Cannot allocate resource for EISA slot 3
[ 8.219293] EISA: Detected 0 cards.
[ 8.249387] TCP cubic registered
[ 8.249399] NET: Registered protocol family 1
[ 8.249423] Using IPI No-Shortcut mode
[ 8.249505] ACPI: (supports S0 S3 S4 S5)
[ 8.249552] Magic number: 3:215:707
[ 8.249931] Freeing unused kernel memory: 328k freed
[ 8.251145] Time: tsc clocksource has been installed.
[ 8.262068] input: AT Translated Set 2 keyboard as /class/input/input1
[ 9.473292] Capability LSM initialized
[ 9.506688] ACPI: Transitioning device [FAN] to D3
[ 9.506692] ACPI: Transitioning device [FAN] to D3
[ 9.506696] ACPI: Fan [FAN] (off)
[ 9.511436] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 9.512873] ACPI: Thermal Zone [THRM] (55 C)
[ 9.887020] usbcore: registered new interface driver usbfs
[ 9.887052] usbcore: registered new interface driver hub
[ 9.887073] usbcore: registered new device driver usb
[ 9.888707] USB Universal Host Controller Interface driver v3.0
[ 9.888761] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
[ 9.888773] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 9.888778] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 9.888947] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 9.888972] uhci_hcd 0000:00:1d.0: irq 3, io base 0x00001800
[ 9.889091] usb usb1: configuration #1 chosen from 1 choice
[ 9.889116] hub 1-0:1.0: USB hub found
[ 9.889122] hub 1-0:1.0: 2 ports detected
[ 9.954669] SCSI subsystem initialized
[ 9.966184] libata version 2.20 loaded.
[ 9.992315] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 9.992321] PCI: setting IRQ 11 as level-triggered
[ 9.992325] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 9.992337] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 9.992342] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 9.992371] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 9.992398] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[ 9.992507] usb usb2: configuration #1 chosen from 1 choice
[ 9.992535] hub 2-0:1.0: USB hub found
[ 9.992543] hub 2-0:1.0: 2 ports detected
[ 9.992684] ieee1394: Initialized config rom entry `ip1394'
[ 10.007074] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
[ 10.007079] e100: Copyright(c) 1999-2006 Intel Corporation
[ 10.118866] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 10.118872] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
[ 10.142801] e100: eth0: e100_probe: addr 0xc2004000, irq 11, MAC addr 00:08:0D:53:B3:CD
[ 10.142983] ata_piix 0000:00:1f.1: version 2.10ac1
[ 10.142995] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[ 10.143215] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 10.143219] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 10.143235] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 10.143301] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011840 irq 14
[ 10.152243] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011848 irq 15
[ 10.152276] scsi0 : ata_piix
[ 3.768000] Time: acpi_pm clocksource has been installed.
[ 3.820000] ata1.00: ata_hpa_resize 1: sectors = 234441648, hpa_sectors = 234441648
[ 3.820000] ata1.00: ATA-7: SAMSUNG HM120JC, YL100-13, max UDMA/100
[ 3.820000] ata1.00: 234441648 sectors, multi 16: LBA48
[ 3.828000] ata1.00: ata_hpa_resize 1: sectors = 234441648, hpa_sectors = 234441648
[ 3.828000] ata1.00: configured for UDMA/100
[ 3.828000] scsi1 : ata_piix
[ 4.148000] ata2.00: ATAPI, max UDMA/33
[ 4.312000] ata2.00: configured for UDMA/33
[ 4.312000] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM120JC YL10 PQ: 0 ANSI: 5
[ 4.312000] scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-7550A 1.P1 PQ: 0 ANSI: 5
[ 4.320000] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 3
[ 4.320000] ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKF] -> GSI 3 (level, low) -> IRQ 3
[ 4.368000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[3] MMIO=[c2006000-c20067ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 4.368000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 7
[ 4.368000] PCI: setting IRQ 7 as level-triggered
[ 4.368000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 7 (level, low) -> IRQ 7
[ 4.368000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.368000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.368000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 4.368000] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.368000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 4.368000] ehci_hcd 0000:00:1d.7: irq 7, io mem 0xc0000000
[ 4.372000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.372000] usb usb3: configuration #1 chosen from 1 choice
[ 4.372000] hub 3-0:1.0: USB hub found
[ 4.372000] hub 3-0:1.0: 4 ports detected
[ 4.392000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 4.392000] sda: Write Protect is off
[ 4.392000] sda: Mode Sense: 00 3a 00 00
[ 4.392000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.392000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 4.392000] sda: Write Protect is off
[ 4.392000] sda: Mode Sense: 00 3a 00 00
[ 4.392000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.392000] sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
[ 4.472000] sd 0:0:0:0: Attached scsi disk sda
[ 4.476000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.476000] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.480000] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 4.480000] Uniform CD-ROM driver Revision: 3.20
[ 4.480000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.840000] Attempting manual resume
[ 4.840000] swsusp: Resume From Partition 8:4
[ 4.840000] PM: Checking swsusp image.
[ 4.840000] PM: Resume from disk failed.
[ 4.888000] kjournald starting. Commit interval 5 seconds
[ 4.888000] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.640000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000039000044a347]
[ 15.416000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 15.440000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.844000] Linux agpgart interface v0.102 (c) Dave Jones
[ 15.844000] agpgart: Detected an Intel 855PM Chipset.
[ 15.860000] agpgart: AGP aperture is 256M @ 0xd0000000
[ 16.184000] iTCO_vendor_support: vendor-support=0
[ 16.184000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 16.184000] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[ 16.184000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 16.208000] input: PC Speaker as /class/input/input2
[ 16.284000] intel_rng: FWH not detected
[ 16.356000] Yenta: CardBus bridge found at 0000:02:0b.0 [1179:0001]
[ 16.380000] pnp: Device 00:09 activated.
[ 16.380000] parport: PnPBIOS parport detected.
[ 16.380000] parport0: PC-style at 0x378 (0x778), irq 5, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 16.412000] ieee80211_crypt: registered algorithm 'NULL'
[ 16.416000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 16.416000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 16.484000] Yenta: ISA IRQ mask 0x0400, PCI irq 3
[ 16.484000] Socket status: 30000007
[ 16.484000] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 16.484000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 16.484000] cs: IO port probe 0x3000-0x3fff: clean.
[ 16.484000] pcmcia: parent PCI bridge Memory window: 0xc2000000 - 0xc20fffff
[ 16.484000] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff
[ 16.548000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
[ 16.548000] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 16.548000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 16.548000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 16.600000] nvidia: module license 'NVIDIA' taints kernel.
[ 17.040000] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[ 17.088000] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
[ 17.088000] PCI: setting IRQ 10 as level-triggered
[ 17.088000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKG] -> GSI 10 (level, low) -> IRQ 10
[ 17.088000] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007
[ 17.176000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0xf6eb1, caps: 0x804713/0x0
[ 17.176000] synaptics: Toshiba Satellite M30 detected, limiting rate to 40pps.
[ 17.264000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 17.268000] cs: IO port probe 0x100-0x3af: excluding 0x1e0-0x1e7
[ 17.268000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 17.268000] cs: IO port probe 0x820-0x8ff: clean.
[ 17.268000] cs: IO port probe 0xc00-0xcf7: clean.
[ 17.268000] cs: IO port probe 0xa00-0xaff:<6>ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[ 17.288000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 17.340000] clean.
[ 18.108000] intel8x0_measure_ac97_clock: measured 55462 usecs
[ 18.108000] intel8x0: clocking to 48000
[ 18.216000] lp0: using parport0 (interrupt-driven).
[ 18.264000] Adding 1052248k swap on /dev/disk/by-uuid/4cb06ab7-c54d-71a3-e23c-a85afbdf58be. Priority:-1 extents:1 across:1052248k
[ 18.452000] EXT3 FS on sda3, internal journal
[ 18.624000] kjournald starting. Commit interval 5 seconds
[ 18.624000] EXT3 FS on sda5, internal journal
[ 18.624000] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.672000] NTFS driver 2.1.28 [Flags: R/O MODULE].
[ 18.752000] NTFS volume version 3.1.
[ 18.792000] NTFS volume version 3.1.
[ 18.828000] NTFS volume version 3.1.
[ 19.588000] input: Power Button (FF) as /class/input/input4
[ 19.592000] ACPI: Power Button (FF) [PWRF]
[ 19.636000] input: Lid Switch as /class/input/input5
[ 19.640000] ACPI: Lid Switch [LID]
[ 19.680000] input: Power Button (CM) as /class/input/input6
[ 19.684000] ACPI: Power Button (CM) [PWRB]
[ 19.720000] ACPI: AC Adapter [ADP1] (on-line)
[ 19.780000] ibm_acpi: ec object not found
[ 19.824000] ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
[ 19.840000] ACPI: Battery Slot [BAT1] (battery present)
[ 19.860000] No dock devices found.
[ 19.900000] Using specific hotkey driver
[ 19.940000] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19a-dev
[ 19.940000] toshiba_acpi: HCI method: \_SB_.VALZ.GHCI
[ 19.944000] toshiba_acpi: Toshiba hotkeys are sent as ACPI events
[ 19.944000] toshiba_acpi: ktoshkeyd will check 2 times per second
[ 19.960000] toshiba_acpi: Dropped 0 keys from the queue on startup
[ 19.964000] pcc_acpi: loading...
[ 23.764000] ppdev: user-space parallel port driver
[ 23.948000] apm: BIOS not found.
[ 24.880000] NET: Registered protocol family 10
[ 24.880000] lo: Disabled Privacy Extensions
[ 24.880000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.052000] Bluetooth: Core ver 2.11
[ 25.052000] NET: Registered protocol family 31
[ 25.052000] Bluetooth: HCI device and connection manager initialized
[ 25.052000] Bluetooth: HCI socket layer initialized
[ 25.128000] Bluetooth: L2CAP ver 2.8
[ 25.128000] Bluetooth: L2CAP socket layer initialized
[ 25.204000] Bluetooth: RFCOMM socket layer initialized
[ 25.204000] Bluetooth: RFCOMM TTY layer initialized
[ 25.204000] Bluetooth: RFCOMM ver 1.8
[ 26.856000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 26.856000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 26.856000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 35.208000] eth1: no IPv6 routers present
[ 78.328000] NET: Registered protocol family 17
[ 79.600000] ieee80211_crypt: registered algorithm 'TKIP'
[ 96.592000] eth1: no IPv6 routers present